Elkay Ezh2o Filter Status Red and Bottles Saved Reads Maintenance

This article contains some of the most common Q&A's pertaining to Elkay ezH2O troubleshooting and maintaining commercial water cooler and bottle filler units. The seamless design of Elkay ezH2O makes them easy to install, proceed make clean, and properly maintained, with a piddling chip of attending and care. Learn how to properly clean your units as per Elkay's recommendations, plus how to supercede the Watersentry filter in your Elkay water coolers as well as reset the filter status for your units both in this quick Q&A style Elkay troubleshooting and maintenance guide.

How often should I clean my Elkay water cooler unit of measurement?

Elkay recommends continuous cleaning in maintaining your Elkay units. How ofttimes depends greatly on a number of factors, including how much traffic your fountain gets, where your unit is located, and water quality.

How should I maintain my Elkay h2o cooler units?

Elkay recommends using a soft cloth (we think microfiber would work well) along with mild dishwashing soap to spray and wipe down the unit. We recommend paying extra attention to the bubbler, push buttons, and other areas of the libation that are oftentimes touched past users.

How do I change the filter on my Elkay ezH2O cooler?

1. When the filter status turns red, or when you know that the filter is due to be replaced then proceed in irresolute the filter.
2. Remove the bottom access console from the lower portion of the water cooler (the panel below the push buttons).
3. Unplug the unit.
4. Unscrew the one-time filter.
5. Replace it with the new Elkay WaterSentry Plus filter.  (Note: there is no demand to turn off the h2o when replacing your Elkay ezH2O water filter.)
6. If you have the filter condition LED lite on the top portion of your cooler, (this will exist on all newer versions of Elkay ezH2O combination water cooler bottle filler units) then you need to reset your filter status to green.

How do I reset my Elkay ezH2O bottle filler filter status?

*The directions below are for units with an LED canteen filler counter.

1. Remove the summit cover of your ezH2O unit.
2. Printing the black reset button located in the tiptop right side, holding for most two seconds earlier releasing.
3. Different messages volition flash beyond the LED interface. When the following message shows on the screen: 'RST FLTR' (shown in the paradigm beneath), printing the blackness reset button in the peak correct side of the inside of the unit again.
4. At this point, the filter condition light should change back to green when correctly reset.
5. Replace the peak cover and your filter condition reset is complete.

How do I make clean the ezH2O flexible fill mat?

1. Remove the 4 screws that sure the flexible fill mat.
2. Remove the superlative section of the mat, and spray the fill mat with a mild dishwashing lather and wipe down with a microfiber (or equivalent) towel, making sure to likewise wipe downward underneath the mat, and the top department of the mat that you removed before.
3. Then simply reassembly and replace the top section of the mat.

How practise I clean the strainer?

To clean the strainer, unscrew the solenoid valve cap. Remove the screen and rinse thoroughly with h2o. Insert screen back onto solenoid valve and make sure o-band is placed properly.

Elkay Water Fountain Troubleshooting Bubbler H2o Stream and Flow

Elkay H2o Cooler Troubleshooting No Water Menses

No Water Flow in EZ, HTV, or electrical middle operated water cooler models:

1. No power to outlet. Check plug and outlet.
2. Wire disconnected from solenoid valve. Reconnect correct wire to solenoid valve.
3. Power cord to water cooler open. You will know this is the cause of no water menstruum is compressor and fn are non working and everything is connected and plugged in). Replace the power cord.
4. Water shut off valve is closed. Open up h2o shut off valve.
5. Lacking regulator valve. Replace the h2o cooler regulator.
6. Water line within of water libation is kinked. Find and unkink water line.
7. H2o is freezing in the evaporator. If water cooler was manufactured prior to 2001 and water is also very common cold, the evaporator may need to be replaced.

Elkay Water Cooler Troubleshooting Water Stream from Bubbler is Too Depression

Below is a numbered list of the most pop potential causes of low menstruum bubbler stream forth with corrective deportment to take to troubleshoot them.

1. If your h2o cooler is newly installed, then the water pressure in your building might only be lower than factory test conditions. Remove the sealant and use Teflon tape or a compression fitting.
2. If newly installed, you may likewise demand to adjust the printing bar adjustment spiral. This is for EHF, WC, HAC, and EMABF Elkay water coolers. Refer to your unit's manual for press bar adjustment screw directions and information.
3. The solenoid may also be the cause of low h2o stream. This occurs when the solenoid will not open up upwards all the way. The models this is applicative to are EZ, HTV, and electronic eye models. If this is the case, the solenoid needs to exist replaced.
4. The strainer screen might as well cause depression bubbler water stream. Clean or supervene upon the strainer screen in this instance.
5. If a new h2o filter is added and the stream becomes low, that filter may cause the water flow to lessen. If this occurs, then you will need to replace the filter.

Other low water flow causes and cosmetic actions:

If your regulator screw is turned as far clockwise as possible and your menstruum is even so likewise low, the following causes may be the culprit:

• Water shut off valve is not completely open up. Open information technology completely.
• Regulator valve is defective or blocked by debris. Supercede the regulator.
• A flexible water line is kinked. Remove insulation to find and remove kink.

Elkay Water Fountain Troubleshooting Water Stream from Bubbler is Besides Loftier

Beneath is a numbered list of the nearly popular potential causes of high menses bubbler stream along with corrective actions to have to troubleshoot them.

1. For newly installed water coolers, the water pressure in your facility may be higher than factory exam atmospheric condition. If this is the case, then refer to your unit of measurement's transmission to learn how to adjust the regulator screw. You will move the screw counter-clockwise until your bubbler stream reaches the desired lowered elevation.
2. The shut-off valve may not be open all the way, causing back force per unit area. Open the close-off valve all the style.
3. Bubbler stream waterway is partially restricted causing dorsum force per unit area or less space to menses through the bubbler causing back pressure. Clean or supplant bubbler.

Elkay Water Cooler Troubleshooting Water Stream from Bubbler Continuous Menstruum

The troubleshooting causes and corrective actions below pertain to EZ, HTV, or electric center operated Elkay h2o cooler models.

1. Water continues to run even subsequently the power cord is unplugged. This means that the solenoid or solenoid diaphragm is defective. Replace the solenoid. You will know the solenoid is the effect is you unplug the power cord and the water menses does non immediately end.
2. If the continuous flow immediately stops when the power string is unplugged, so in that location are two reasons yous may exist experiencing continuous flow:

Either the press bar is sticking and property the microswitch downwardly and you need to supplant the press bar or it needs to be adjusted, or the micro switch behind the press bar is defective and needs to be replaced.

Find all of the repair parts needed to service your Elkay ezH2O water cooler units in our Elkay repair parts section . If y'all don't see the repair part needed to repair your unit, remember that we practise not list all of the thousands of Elkay repair parts we carry, many of which are in stock. Requite u.s. a call to gild any parts you lot exercise non see online at 800-442-6622. Telephone hours are Monday through Fri, 7:thirty AM - 5:00 PM EST.

Hopefully, this article helps yous identify the cause of event for your h2o cooler, along with how to fix it and get your Elkay unit back in proper working society. We highly recommend frequently cleaning your unit to keep it sanitary for users to and avert early wear of your units. Subscribe to our newsletter in the black box below to detect out about more than Elkay water fountain troubleshooting guides we brand in the future, every bit well equally other h2o libation manufacturer information, tips, and resources to make maintaining, troubleshooting, and purchasing water cooler units and repair parts easier.

Here are links to related troubleshooting articles and resources:

•How to Replace an Elkay ezH2O Bottle Filler Filter and Reset Filter Light
• Retrofit Bottle Filler Guide for Elkay Water Fountains
•Water Cooler Filter Comparison Chart
•  Oasis Water Cooler Troubleshooting
• Photographic Parts Breakdowns (Shown/Linked below)

Elkay EZS8L Parts Breakup (photographic)
This parts breakdown applies to both Elkay EZS8L and EZS8S water cooler units.
View the Elkay EZS8L Parts Breakdown

Elkay LZS8L Parts Breakdown (photographic)
This parts breakup applies to both Elkay LZS8L and LZS8S h2o cooler units.
View the Elkay LZS8L Parts Breakdown

*Note: to view h2o cooler and other unit manuals and parts breakdowns, go to the unit of measurement product page and notice the links at the bottom of that unit of measurement's description.

For one on 1 support for your water cooler units, requite us a telephone call to speak to one of our production experts.

Toll-Free: 800-442-6622

Pittsburgh: 412-781-9100

nisbetorpon1948.blogspot.com

Source: https://equipartsdrinkingfountains.com/blogs/articles/elkay-ezh2o-troubleshooting-and-maintenance-guide

Share this post